Inputs and application for grapes
Case 1 Copper and sulfur in the sprayer - 1
Pick the plot first Open a new chat and tap Plots (All) under the question box. Choose the plot you want advice for. ORTH then works from that plot’s crop, variety, soil and documents, and from the farm weather. For grapes Pick one plot of one variety. We picked Lote 1: Tempranillo on 110 Richter, 1.97 ha of clay soil with drip, 5,470 vines from March 2015 on a trellis with a double cordon. Harvest finished on 25 September and the vines are at leaf fall. Every number below is for that plot. - 2
Start from the Machinery & Equipment button For doses and sprayers, tap Machinery & Equipment. ORTH can calibrate your sprayer for a product rate and tank size, check whether your pump and emitters can deliver a plan, or turn a fertigation recipe into injector settings. For grapes In a vineyard the canopy in early spring is a fraction of the canopy in summer, so the water per hectare changes through the season. That is why the dose starts from a calibration. - 3
Name the product, not the active ingredient We asked how to dose copper and sulfur next spring with a 1,000 L airblast sprayer, whether they can share a tank, and what to use on pruning wounds. ORTH started with a correction: copper and sulfur are active ingredients, and Spain’s register authorizes products for a crop and a use. It asked for the trade names so it can check them. The dose, the timing and what mixes depend on the exact product and its formulation. Copper mainly works against downy mildew and sulfur mainly against powdery mildew, so apply each for the risk you have, not both by routine. - 4
Calibrate, then work out the tank First calibrate the sprayer with clean water as you will spray in spring: the same tractor speed, pressure, nozzles and fan. Spray a measured area and note the water used. Spray volume in L/ha is litres used divided by hectares covered, and a full tank covers 1,000 divided by that volume. For a label rate per hectare, product per tank is the rate times the hectares that tank covers. For a rate per hectolitre, a 1,000 L tank is 10 hL. Do not assume one tank treats one hectare. ORTH’s example was a registered copper and sulfur premix at 4 to 6 L/ha: 7.88 to 11.82 L for the 1.97 ha of Lote 1. Its register entry allows 8 applications at 7-day intervals, with 7 days before harvest, and limits copper to 28 kg per hectare over seven years. Always follow the product label. - 5
Copper and sulfur in one tank Can they share a tank? ORTH said not automatically. Some registered products contain both, but that does not show that two separate products mix. For both mildews at once, use a registered premix whose label covers both. Mix separate products only when both labels allow it: check the formulation, the crop stage, the water pH and the mixing order, then do a small jar test. A jar test shows whether the mix stays stable. It does not replace the label or prove the mix is safe for the crop. Do not mix sulfur with mineral oil, and keep the 21 days the label asks before or after an oil. Do not mix sulfur with alkaline products or apply it in strong heat. With less canopy, lower the water by closing nozzles and adjusting the air, never by going above the label concentration. Case 2 Pruning wounds this winter - 6
Use a product registered for wounds For the pruning wounds, ORTH found no copper or sulfur product authorized for that use on wine grapes. It showed the authorized alternative: a ready-to-use product with pyraclostrobin and boscalid, registered for pruning wounds on grapevine against the fungi of esca, black dead arm and Eutypa dieback. It goes straight on the wounds, undiluted, during dormancy, in one application, so it does not go through the 1,000 L sprayer. The amount depends on how many wounds there are and how big they are. In the diagnosis chat ORTH also showed a Trichoderma atroviride product, sprayed or brushed on within two weeks of pruning. Treat fresh wounds soon, in a dry spell, the large cuts first. Always follow the product label. - 7
What changes for table grapes Table grapes are a separate crop in the register, so an authorization for wine grapes does not carry over. Check that the label names table grapes, the disease, the crop stage, the pre-harvest interval and the maximum number of applications. A denser canopy and bigger bunches can mean a 1,000 L tank covers less area: improve the coverage, and leave the rate per hectare alone. Visible sulfur deposits and copper stains matter on fruit sold fresh. Open the bunch zone for air and spray without causing sunburn. The EU limit ORTH showed for copper is 100 mg/kg for wine and table grapes, but buyers of table grapes may set stricter limits or their own lists. For the exact tank amount, ORTH asked for the trade names or photos of the labels and the hectares one tank covers after calibration.
1.
2.
3.
4.